Showing 141–160 of 185 results
-
$30.00
Features Controlled pressure assures positive, adjustable contactthrough full range. Operates with any electric drill.Furnished with 3″ long 220 grit stones, see below for othergrits. Adjustable stop collar permits quick selection of tworange settings, from 2″ to 4″ and from 4″ to 7″. Stone armsare easily compressed to eliminate cylinder scratches.
-
$37.00
Features 3/4″ Low Profile Design Quickly and Easily Disengages theLine from Jiffy-tite Quick-Connect Fittings without Removalof the Clip.The teeth of the tool fit perfectly into tight tolerance ofJiffy-tite? connectors and when rotated allow the line to bepulled without damageto the connector or retaining clip so they can be reused.
-
$24.00
Features Extra Low Profile Design Quickly and Easily Disengages theMost Popular Size of Jiffy-tite Quick-Connect FittingsWithout Removal of the Clip. Teeth of the tool fit perfectly into tight tolerance ofJiffy-tite? connectors and when rotated allow the line to bepulled without damage to the connector or retaining clip sothey can be reused. Tool fits the most…
-
$8.00
Features A quick, easy way to pinch off vacuum lines, fuel lines,brake lines, etc. without damaging the line. Sold two perset.
-
$29.00
Features Use with a ratchet or impact wrench to pull the new studsecurely in place. Position the tool over the stud shaft.Tighten the lug nut against the tool to pull the stud inplace. Works on most all automotive and light-duty truckwheel studs, foreign and domestic. NOTE: The bearingwill wear with use and isnot warranted.
-
$45.00
Features Locks Flywheel in Place When RemovingHarmonic Balancer on 6.6L Duramax Engineswith Allison Automatic Transmissions.Saves time by locking the flywheel at the transmissioninsteadof having to remove the starter for water pump replacement.On 2500 and 3500 pickups, remove metal spring-loadedinspection plate on the bottom of the transmission. Toolshouldslide into opening toward engine with the top of…
-
$21.00
Features Provides an Easy Way to Check Ignition Systems with Coil-OnPlugs. Applications Include Ford, Chrysler, Mitsubishi,Nissan and More. It is the quickest way to test for no-start conditions. An inductive test cannot be performed, because there areno plug wires. High visibility white lettering makes iteasy to read the gap measurement from 0 to 40k. Theround…
-
$30.00
Features Easy reading gauge assures accurate vacuum and pressurecheck. Dual pressure 0-15, Vacuum .30, (not for Diesel)
-
$42.00
Features Compression Tester Quickly and Accurately Check Compressionon Gasoline Engines. Gauge registers 0 – 300 P.S.I. and 0 -2100 kpa. Fits 14mm and 18mm thread sizes.
-
$10.00
Features Fits Spark Plug Holes with Limited Access.The narrow profile and long length allows access to sparkplug holes in confined spaces. Use with a 3/8″ ratchetorextension. Size: M14x1.25 IMPORTANT: Use anti-seize.
-
$22.00
Features Quickly Evacuates Air from Tires WithoutRemoving the Valve Core.Simply replace a standard sized valve cap with this handytool and the special design will depress the pin in thevalvecore. Large openings on the sides of the tool allow air toescape quickly from the tire. Tools are marked so tires canbe returned to their original position…
-
$22.00
Features The Lisle spring clutch assures a proper fit on the pistonand a positive locking action. Range 2 1/8″ to 5″.
-
$11.00
Features With the engine running, place the grooved end of the toolover the plug wire. The bulb will flash to indicate spark.
-
$27.00
Features Quickly Removes the U-Joint Cap fromthe Drive Shaft on Most Rear Wheel DriveVehicles.Use the driver with an air hammer to remove u-joint caps upto 1-5/16″ diameter. Prevents damage to drive shaft and axleshaft ears, when presses or chisels are used. On somevehiclesthe u-joint is retained with plastic from the factory. Theplastic must be removed…
-
$26.00
Features Torque tool is set to 4 inch pounds, to prevent under andover torquing the valve core. Helps prevent valve core leakscausing low tire pressure and possible TPMS alerts. Slimdesign allows access in tight spots.
-
$22.00
Features Stepped design helps keep tool from bouncing back. The 18530is used to replace worn out ball joints and to remove CVdrive shafts on FWD vehicles. The tine opening is 15/16″.These heavy-duty tools are drop forged and heat-treated forlong use. Steps can be sharpened if needed.
-
$22.00
Features Stepped design helps keep tool from bouncing back. 18520 isused to replace worn out tie rods and to separate shockabsorber links. The tine opening is 11/16″. These heavy-dutytools are drop forged and heat-treated for long use. Stepscan be sharpened if needed.
-
$19.00
Features Small Engine Ring Compressor For Small Cylinders: 1 1/2″ to3″ (38.1-76.2mm) Quality tool at a low price.
-
$45.00
Features Cross-Cut Tip Design that Grip Most Hose Clamps fromMultiple Angles. Ergonomic curved design making pliers easy to use inhard-to-reach areas. Ratcheting lock mechanism holds the clamp in an openposition for hands-free use. Dual material grips for comfort. Works on most springhose clamps.
-
$42.00
Features Cross-Cut Tip Design that Grip Most Hose Clamps fromMultiple Angles. Ergonomic curved design making pliers easy to use inhard-to-reach areas. Ratcheting lock mechanism holds the clamp in an openposition for hands-free use. Dual material grips for comfort. Works on most springhose clamps.