Showing 1–20 of 35 results
-
CV CAL-VAN CV18640 Intermediate Pitman Arm Puller
$108.00Features Intermediate Pitman Arm Puller is designed to removepitman arms on intermediate trucks, school buses, deliverytrucks and other vehicles with a nut release pitmen arm. High -strength steel casting for high-capacity pulling. Eliminates hazardous hammering and cutting torchmethods. May be used with up to a 1/2″ drive impact tool. Applications: Heavy-Duty trucks, buses, utility vans,delivery…
-
MU MUELLER-KUEPS MU609390 XS Press And Pull Sleeve Kit
$522.00Features Universal Tool set for extracting and mounting: silentbearings, hydraulic bearings, ball bearings, rubberbearings, shaft seals, bearing brush, etc. Includes: 10 sleeves, 3 spindle, 4 discs
-
MU MUELLER-KUEPS MU433414 Uni Drive Shaft Pusher / HUB Puller
$260.00Features Damage to the drive shaft thread is prevented. Suitable for almost 4- and 5-hole wheel HUBs with apitch circle diameter up to 136 mm. The “VIBRO-IMPACT” principle: the vibration impact ofthe pneumatic wrench is transmitted to the wheel HUB and tothe drive shaft through the trapezoidal thread spindle. When used in conjunction with the…
-
OT OTC OT7927A Steering Wheel Remover/Lock Plate Compressor Set
$86.00Features Included with the puller are four sets of cap screwsneeded for the various thread requirements. A steering wheel lock plate compressor is also includedto compress the steering wheel lock plate to remove orinstall the snap ring. A steering pivot pin remover for Saginaw steeringcolumns completes the set, and it all comes in a convenientplastic…
-
OT OTC OT7318 Pilot Bearing Puller
$136.00Features Designed to pull flywheel pilot bearings in closequarters where a slide hammer cannot be used. Operates onmany models with engine in chassis. Capacity: 1/2″ to 1-1/2″. I.D. reach 3/4″.
-
OT OTC OT7075 Transmission Output Shaft End Yoke Remover
$149.00Features Transmission output shaft end yoke remover.Features Puller supplies you with 10 tons of mechanicalpower.
-
OT OTC OT7070A Truck Transmission Bearing Service Set
$624.00Features The set is designed to help you remove input shaft bearingsand countershaft bearings, in both the main and auxiliaryboxes of heavy-duty Fuller transmissions. It will alsoremove end yokes from 1600/1610-1810 series transmissions.The puller delivers 10 tons of mechanical power- essentialforce for working on big gearboxes. Works on Fuller twin-countershaft transmissions: 125,600, 660, 900, 9500,…
-
OT OTC OT6777 GM Duramax Injector Puller
$107.00Features Assists in removing injectors from the cylinder headwithout damaging the injector body. Similar to OE tool #EN-49774. Applications include: 2011-later 6.6L Duramax Diesel andIsuzu engines
-
OT OTC OT6701 Pitman Arm Puller Set
$307.00Features This set contains three pitman arm pullers for a wide rangeof applications from 1993 and later GM, Ford, Dodge and Jeepapplications. Includes OTC 8150 conical pitman arm puller, 6496compact pitman arm puller and 6497 super-duty pitman armpuller.
-
OT OTC OT6669 Harmonic Balancer Puller Kit
$123.00Features Designed for removing the harmonic balancer in tightengine compartments without removing the radiator. This kit includes an extra set of jaws to cover moreapplications and vehicles. Kit also contains the 3-jaw puller, four lengths offorcing rods, and a forcing screw with a 3/8″ internalsquare drive for ratchet use, and a 3/4″ external hex forwrench…
-
OT OTC OT6358 Chrysler Products Alternator Decoupler Pulley
$93.00Features This tool holds the alternator shaft in place so thedecoupler pulley can be removed and installed. Male andfemale ends are 10mm. Applications include 2004-Later Chrysler/Dodge/Jeepvehicles. Similar to OE part number MLR-8433A.
-
OT OTC OT522 Large Gear Pulley Puller
$88.00Features Puller will spread from 2″ to 7-3/4″ Cross Block is 8-1/4″ wide Forcing screw is 3/4″-16 x 11-5/8″ long Accommodates any cap screw up to 1/2″ diameter
-
OT OTC OT5190A U-Joint Puller
$321.00Features Larger diameter threaded shaft can handle U-joints thatare severly seized and require higher force to pull andinstall. Major tool components are heat treated for improvedstrength and durability. Smoother thread allows for a lower, more consistenteffort to rotate shaft. Designed to fit all Class 7 and 8 trucks, including awide variety of drivelines from Spicer…
-
OT OTC OT5055 Manual Slack Adjuster Puller
$147.00Features Will yank even the most corroded slack adjuster off theS-cam and do so in just a fraction of the time needed withheat and beat methods. Rugged forcing screw and caststeel body. Also a pitman arm pulleron 2500/3500 Silverado, Sierra and RAM Trucks 2011 ? Current Chevrolet Silverado, GMC Sierra 2500 AND3500 trucks 2009, 2013…
-
-
OT OTC OT4680 Wiper Puller
$88.00Features The 4680 Wiper Puller from OTC has a unique design wherejaws are forged with radius to hug the center screw forminimal spread, and for accessing recessed components. Theradius also ensures optimal contact with object beingpulled. It comes with 2 pair of legs – 9/16″ width and 1″width – for many types of small component…
-
OT OTC OT4676 Windshield Wiper Puller Only
$20.00Features Removes wiper arms on many foreign and domestic cars andlight trucks. Will not damage wiper arm or hood cowling during removal Simply place puller feet under wiper arm and tightenforcing screw against wiper shaft.
-
OT OTC OT4581 Blind Hole Bearing Puller Set
$240.00Features For jobs requiring an inter pull.Four collect sizes: 3/8″ to 1/2″, 9/16″ to 11/16″, 5/8″ to1″ to 1-1/4″, and a 2-1/2″ pound slide hammer.
-
OT OTC OT4532 7 Ton Multi Purpose Bearing and Pulley Puller Kit
$225.00Features Wide Spread Crossbar with 3 pin-hole; 7-1/4? to 9? 2 pair of long reach jaws gives user reach options of5-1/2? and 9-1/2? 2 long reach forcing screws (live center) for pushes of4-1/2? to 10-1/2? Accepts shorter jaws from 4534 kit 7 Ton version of our Multipurpose Bearing and PulleyPuller Set
-
OT OTC OT4422 Pilot Bearing Puller
$66.00Features Pilot Bearing Puller uses a durable bridge to bear the forceof the pull. Restriction plate catches the bridge and prevents thejaws from spinning when force is engaged. Jaw spread covers ranges of 1/2″ to 1 1/2″ and 3/8″ to1 3/8″ for greater application. Reach has a min/max range of 3/16″ to 1 1/4″.
