OT OTC OT6881 Crank Sensor Alignment Tool
$83.00Features Aligns the crankshaft position sensor properly duringinstallation. Similar to 303-1521. Applications include:2012-Later 2.0L Duratec, EcoBoost and GTDI2015-Later 2.3L EcoBoost
USA Free Shipping on orders of $140.00 or more
Showing 21–40 of 111 results
Features Aligns the crankshaft position sensor properly duringinstallation. Similar to 303-1521. Applications include:2012-Later 2.0L Duratec, EcoBoost and GTDI2015-Later 2.3L EcoBoost
Features Applications include 2009-Later select Ford, Lincoln,Mercury vehicles Similar to OE part number 211-061
Features This IPR Socket actually combines two OE tools into one.Again, the configuration for the IPR changed in 2005 and asecond tool was developed for the change. However, ourAftermarket engineers worked with specialized technicians todevelop one tool that can address either version of the IPR? giving today’s technicians a cost-effective tool.
Features Ensure replacement injectors and seals are installedcorrectly. This kit installs the dual seals onto the end of theinjector. These seals must be installed into their grooves, andthen sized to the engineered dimension before the injectorsare installed into their bores in the cylinder head Applications include 2010-later GM engines found in manyBuick, Cadillac, Chevrolet and…
Features Save time removing crankshaft rear seals, preventingdamage to the block and crank. This seal remover is a special puller with three jawsdesigned to grab the inner lip of the seal. The forcing screw attached to the center plate is usedto react against the crankshaft end to pull the seal out. Eliminates damage to the…
Features Makes replacing engine drive belts and startergenerators easier. This tool compresses the belt tensioner spring duringengine drive belt replacement and starter generatorservicing. Applications include 2.4L GM eAssist engines found in:2012 – 2016 Buick LaCrosse, 2012 – 2017 Buick Regal, 2011 -2014 Chevrolet Malibu
Features Oil seal and wear ring installer for 5.0 inch diameter seals Makes the difficult job of correctly installing the rearcrankshaft seal and wear ring on most Navistar DT-360 andDT-466 engines thru 1996 an easy task Bolt the adapter to the crankshaft and wrench thecomponent home Eliminates damage to seals or wear ring that can…
Features Set includes: 4673-1 29 mm Pressure / Vacuum Switch Socket 4673-2 7/8″ Vacuum Switch Socket 4673-3 27 mm Oil Pressure Sending Unit Socket 4673-4 7/8″ Vacuum Switch Socket 4673-5 1-1/16″ & 1″ Oil Pressure Sending Unit Socket 4673-6 7/8″ Long Oxygen Sensor Socket 4673-7 7/8″ Short Oxygen Sensor Socket
Features # Designed to remove oil and grease seals when servicingcars, SUVs and light trucks without damaging the housing orbearing.# Hook tips in two sizes and professional handle designallows removal of hard-to-get-at seals by getting underthem.# The hook tip is double-secured versus competitors, forsafety and durability.# An extra blade is included, and additional replacements(No. 4508-1)…
Features # Permits installation of tapered bearing races and sealswithout damage to the component or housing. Includes adriver handle plus popular bearing and seal drivers, rangingfrom 1.565″ to 3.180″.# Tapered side of driver is used to install races. Invertthe driver to the flat side to install seals. Set is housedin a blow-molded plastic storage case.#…
Features # Enables you to remove and install bushings ranging from3/8″ to 1-3/8″ in diameter, as used in cars, trucks,tractors, construction equipment, electric motors, and manyother components having bushings.# Includes: Large, medium, and small driver handles withnuts; sixteen bushing adapters ranging from 3/8″ to 1-3/8″.# Housed in a blow-molded storage case.
Features Cut service time for bushing removal dramatically Removes and installs single-wrapped FAS II AirlinerFreightliner Rear Suspension bushings in a fraction of thetime of traditional methods. Saves on average 45 minutes per bushing (4 per vehicle)on flat rate of 1.5 hours per bushing. 15-ton capacity cylinder.
Features Sleeve Puller / Installer Sets: These sets work on awide array of truck, bus, and tractor engines, as well asthose in other vehicles. They’ll handle wet and dry sleeves- and you won’t need to remove head studs. Save time,effort, and money. – Choice of two sets: manual or 17-1/2ton hydraulic powered. – Wide range…
Features The folllowing adapters are included: MVA662 Ford PowerSteering Adapter; MVA661 GM Power Steering Adapter; MVA660Universal Power Steering Adapter Featuring a robust design and construction, all threeadapters include an inline, barbed connection for a 1/4 in.internal diameter hose. These adapters form an airtight seal in the neck of avehicle?s power steering pump allowing for air…
Features Removes plastic fuel pump retaining rings. versal adjustable design fits most plastic retainingrings. Prevents damage to original pump retaining ring. Use with ?” drive extension and ratchet. Use to re-install old retaining ring. Removes plastic fuel pump retaining rings. Universal adjustable design fits most plastic retaining
Features Combustion Leak Detector Quickly Pinpoints Combustion Leaks.Checks for combustion leaks caused by bad head gaskets,cracked blocks, and cracked or warped heads. Fluid changesfrom blue to yellow when exposed to combustion gases fromthe radiator. Diesel Test fluid sold separate. Coolant carbon checker
Features Removes Broken Exhaust Manifold Bolts on Duramax 6.6L DieselMotors Without Damaging the Cylinder Head. Tapered boltscenter base plate over bolt holes and slip fit bushingallows you to move from hole to hole without moving baseplate. Drill depth gauge to make sure water jacket is notpierced. The screw extractor is then used to remove thebroken…
Features Removes Broken Exhaust Manifold Bolts on Ford 7.3L DieselMotors Without Damaging the Cylinder Head. Tapered boltscenter base plate over bolt holes and slip fit bushingallows you to move from hole to hole without moving baseplate. Drill depth gauge to make sure water jacket is notpierced. The screw extractor is then used to remove thebroken…
Features Helps Make a Really Tough Job Easier to Complete. Helps Beatthe Flat Rate. Designed to remove broken exhaust manifold studs on4.6L, 5.4L and 6.8L V10 2 valve and 3 valve Ford Tritonengines without damaging the cylinder head. Interchangeable plates and alignment pins help centerdrill on the broken stud. Depth gauge for drilling is marked…