Showing 61–80 of 229 results
-
$110.00
Features Designed to be used with EVAP system tester. Includes a male tank adapter and female cap adapterconnected by a 20″ hose. Applications include:2006-Later Chrysler/Dodge/Jeep vehicles1999-2003 Mitsubishi Gallant2001-2005 Mitsubishi Eclipse Spyder Similar to OE part number MLR-8382.
-
$43.00
Features Adapts to fuel system for use during pressure testingand diagnostic procedures. For use on 2003-Later 5.9L Cummins Diesel. Similar to OE part number MLR-9011.
-
$71.00
Features This IPR Socket actually combines two OE tools into one.Again, the configuration for the IPR changed in 2005 and asecond tool was developed for the change. However, ourAftermarket engineers worked with specialized technicians todevelop one tool that can address either version of the IPR? giving today’s technicians a cost-effective tool.
-
$42.00
Features This pair of High Pressure Fuel Rail Adapters is required toconnect to the vehicle’s fuel line. The fuel line connectionchanged in 2004 ? so the two adapters give you thecapability to address either platform for pressure testing.
-
$91.00
Features Installs the front crank seal with the cover on or offthe engine. The bolt is threaded into the crankshaft and the nut istightened to seat the seal. Similar to EN-50820 & EN48034. Applications: 2013-14 Cadillac ATS, 2014 Cadillac CTS,2013-14 Chevrolet Malibu, 2014 Chevrolet Impala and BuickRegal 2.0L and 2.5L engines.
-
$178.00
Features Ensure replacement injectors and seals are installedcorrectly. This kit installs the Teflon seal onto the end of theinjector. The pilot cone is placed onto the end of the injectorand the seal is started over the cone. The installer pushes the seal into the groove on theinjector tip. Applications include: 1998 – 2014 GM engines…
-
$203.00
Features Ensure replacement injectors and seals are installedcorrectly. This kit installs the dual seals onto the end of theinjector. These seals must be installed into their grooves, andthen sized to the engineered dimension before the injectorsare installed into their bores in the cylinder head Applications include 2010-later GM engines found in manyBuick, Cadillac, Chevrolet and…
-
$345.00
Features Save time removing crankshaft rear seals, preventingdamage to the block and crank. This seal remover is a special puller with three jawsdesigned to grab the inner lip of the seal. The forcing screw attached to the center plate is usedto react against the crankshaft end to pull the seal out. Eliminates damage to the…
-
$69.00
Features Save time servicing fuel line bundle or replacing fuellines. This quick-connect release tool is designed toseparate the 4.8mm (3/16 inch) hydrocarbon injectionquick-connector. Allows access to and service of the fuelline bundle and fuel line replacement without removal ofunrelated components. Also helps prevent possible damage tothe fuel line bundle. Similar to OE tool #CH-49736. 2010-later…
-
$156.00
Features # Required for use with No. 6735 Sprinter Van Ball JointKit. When used with OTC No. 6730 Update Kit, you can expandthe applications of OTC Nos. 7249, 7918, and 6530 BallJoint Kits.
-
$131.00
Features Four-piece kit designed to be used with the industrystandard OTC No. 7248 C-frame. Contains specialty ball jointadapters to fit the following GM vehicles: TrailBlazer &Envoy 2002-2005 Suburban & Tahoe 1995-2004 Avalanche 2002-2004 Escalade 1999-2004 Express & Savana 2003-2004 Hummer H2 2003-2004
-
$130.00
Features Three-piece kit contains specialty ball joint adapters forusewith the industry standard OTC No. 7248 C-frame.Designed to work with the following Ford vehicles: F-150 1997-2003 F-250 1997-2004 F-350 1992-2004 F-450 1999-2002 F550 1999-2002 Excursion 2000-2004 Expedition 1997-2002 Explorer 1995-2004 Ranger 1998-2004
-
$292.00
Features Makes replacing engine drive belts and startergenerators easier. This tool compresses the belt tensioner spring duringengine drive belt replacement and starter generatorservicing. Applications include 2.4L GM eAssist engines found in:2012 – 2016 Buick LaCrosse, 2012 – 2017 Buick Regal, 2011 -2014 Chevrolet Malibu
-
$81.00
Features Verifies that the camshaft fuel pump lobe is at basecircle position before installing the high pressure fuelpump. Tool indicates the pump may be installed when it isflush to manifold surface. Similar to EN-51092. Applications: 2014-15 Chevrolet Silverado & GMC SierraV6 and V8 engines, 2015 Chevrolet Suburban/Tahoe, GMCYukon/XL, 2014 Chevrolet Corvette, 2015 Cadillac Escalade V8engines
-
$29.00
Features Two-piece kit includes tools to properly size the sealand install the seals in the proper groove on the injectortip for leak-free operation. Works to install both seals on the injector tip. Similarto EN-51105. Applications: 2014-15 Chevrolet Silverado & GMC SierraV6 and V8, 2015 Chevrolet Suburban/Tahoe, GMC Yukon/XL, 2014Chevrolet Corvette, 2015 Cadillac Escalade.
-
$174.00
Features Used for removal of the direct injection fuel railwithout damage. The rail assembly must be removed as straight aspossible to prevent damaging an injector bore in thecylinder head or the mount assembly. Similar to EN-49248. Applications: 2007-2014 General Motors Direct InjectionEngines including those used in Pontiac, Saturn, Cadillacand Chevrolet vehicles.
-
$134.00
Features Correctly installs the seal onto the axle shaft and intothe wheel knuckle,preventing front hub vacuum leaks that would cause the 4WDto not engage. Works on 2005-newer Ford F-450, F-550, 4X4s having thevacuum-operated front axle.
-
$120.00
Features Correctly installs the seal onto the axle shaft and intothe wheel knuckle,preventing front hub vacuum leaks that would cause the 4WDto not engage. Works on 2005-newer Ford F-250, F-350, 4X4s having thevacuum-operated front axle.
-
$116.00
Features Works on 1998?newer Ford F-250, F-350, F-450, andF-550 4X4s having the vacuum-operated front axle. Correctly installs the seal onto the axle shaft andinto the wheel knuckle, preventing front hub vacuumleaks that would cause the 4WD to not engage. Similar to Ford tool No. 303-429
-
$76.00
Features Oversized retaining plates lock camshafts together attop dead center (TDC) on GM 2.8L 3.0L and 3.6L DOHC engines. Three-plate set is used to tighten both sets of cams toprevent them from turning while setting timing. Extra-large size prevents valve covers from beinginstalled with the plates in place, protecting the engine. Similar to EN-48383.