Showing all 12 resultsSorted by popularity
-
OT OTC OT6637-ST Strut Tamer II Extreme with Stand
$1,925.00Experience the pinnacle of strength and safety with the OT OTC OT6637-ST Strut Tamer II Extreme. This spring compressor meets ASME PASE safety standards, ensuring safe compression of even the largest strut springs. With features like forged locking jaws, extra-thick compression arms, and a convenient stand, it’s the ultimate tool for your shop. Introducing the…
-
TA TOOL AID TA63000 Universal Macpherson Strut Coil Spring Tool
$60.00Features The Strutter?2 MacPherson Strut Coil Spring ToolWith acme threads and economically priced. virtually allQuickly and easily work on the MacPherson Struts found onvirtually all modern domestic and imported vehicles.Features a one piece cold headed bolt made of chromiummolybdenum alloy steel. The nuts are Grade 5.Use with impact wrench or hand tool ON or OFF…
-
TA TOOL AID TA62200 Single Action Coil Spring Compressor
$71.00Features Single Action Coil Spring CompressorRemove, install and compress coil springs that can bereached through the center of the coil.Acme threads.
-
TA TOOL AID TA61800 Strut Alignment Level
$42.00Features Strut Alignment LevelUse to restore strut to original alignment position afterrepair or replacement.Super strong magnet mounts on brake rotor or spindle.Works on all vehicles equipped with MacPherson Struts.
-
-
OT OTC OT6637 Strut Tamer II Extreme
$1,476.00Features The 6637 Strut Tamer II Extreme sets the standard instrength and safety for strut spring compressors. This unitmeets the new ASME PASE safety standards for springcompressors and is capable of safely compressing the largeststrut springs. Forged locking jaws includes larger pads and offset toclamp onto and compress springs even tighter than before Extra thick…
-
OT OTC OT6582 Struttamer Elite Stand
$315.00Features The OTC StrutTamer Elite stand features steel frameconstruction with two wheels that allow you to easily tiltthe stand back and move the entire unit to the work area. Tokeep it firmly in place during compression, the wheels liftoff the floor, and four no-slip rubber pads keep the standfirmly in place during operation. The stand…
-
OT OTC OT6494 Clamshell Strut Compressor
$315.00Features Servicing MacPherson struts is convenient and affordablewith this compressor. It fits a wide range of struts andrequires no special adapter shoe. Safety locking pins hold the compressor jaws in place. Tool compresses springs of 4″ to 9″ O.D., with wirediameters of 7/16″ to 11/16″. Built to use with an impact wrenc
-
CM CTA MANUFACTURING CM7466 15 Pc. Shock and Strut Service Kit
$184.00Features Addresses the most common issue of tightening the topmount nut while holding the strut. Allows for proper torque to be applied to the top nut.Constructed of Chrome Vanadium. Includes: 82mm Deep Sockets sizes: 16, 17, 18, 19, 21,22 & 24mm. 4 Hex bits: 5, 6, 7 & 8mm, Sliding T-Bar, 21mmGo-Through Ratchet and 2…
-
CM CTA MANUFACTURING CM4005 VW/Audi Suspension Strut Housing Socket
$14.00Features Special oval shaped bit end services Suspension StrutHousing Nuts found on some VW & Audi models Also fits some BMW, Seat, Renault, Peugeot 3/8″ square drive
-
CM CTA MANUFACTURING CM3755 10 Point Lower Control Arm Socket for Honda and Acura
$11.00Features 10 point x 19mm socket services selected Honda/Acurarear trailing arms. 1/2? drive.
-
CM CTA MANUFACTURING CMA446 Volvo Strut Nut Socket Set for Removing and Installing Top
$27.00Features Use for removing and installing the top shock retainingnut on S40, S60, S70, S80, S90 models Includes holding socket and double-D axle center socket Double-D measures 8mm “flat-to-flat” Use 10mm hex wrench on top of Double-D socket Use 28mm hex wrench on holding socket Black finish
