Showing 81–100 of 335 results
-
$323.00
Features Removes the front seal and wear ring from crankshaft.Similar to 303-1260.260. Applications include:2008-2010 Ford F-250, F350, F450, F-5506.4L Ford Powerstroke enginesVT365-MaxxForce7Navistar International
-
$196.00
Features The OTC 6887 Crankshaft Front Seal and Wear RingInstaller installs the front seal and wear ring oncrankshaft. It’s designed to eliminate lip flare on the wearsleeve and installs the seal properly. Use OE part number303-1158 for 4.5L installation. Applications include Ford vehicles using the followingengines:2003-2007 F-250, F350, F-450, F-550, Excursion2004-2007 F-650, F-7502004-2010 E150, E-250,…
-
$284.00
Features Removes the front seal and wear ring from crankshaftSimilar to OE part number 303-762
-
$405.00
Features Removes the rear seal and wear ring from crankshaft Similar to OE part number 303-771
-
$110.00
Features Features a 1/2″ square drive opening in handle for extraleverage.Similar to OE part number 303-126
-
$83.00
Features Aligns the crankshaft position sensor properly duringinstallation. Similar to 303-1521. Applications include:2012-Later 2.0L Duratec, EcoBoost and GTDI2015-Later 2.3L EcoBoost
-
$78.00
Features Applications include 2009-Later select Ford, Lincoln,Mercury vehicles Similar to OE part number 211-061
-
$78.00
Features Power Steering Evacuation Cap allows for removal of air fromthe power steering system when used with a vacuum pump. Airin the system can cause noise and premature pump failure. Fits various power steering pump reservoirs. Similar to 211-265.
-
$160.00
Features The OTC 6867 Hub Seal Installer is used to install the wheelhub oil seal on single or dual wheel axle assemblies. Theseal installer adapter is driven with the 7″ detachablehandle. Applications with Ford, Lincoln and/or Mercury vehiclesusing the following axles:1999-later DanaFord 10-1/2″ Full Floating Axle. Similar to OE part numbers 205-422 and 205-153.
-
$110.00
Features Designed to be used with EVAP system tester. Includes a male tank adapter and female cap adapterconnected by a 20″ hose. Applications include:2006-Later Chrysler/Dodge/Jeep vehicles1999-2003 Mitsubishi Gallant2001-2005 Mitsubishi Eclipse Spyder Similar to OE part number MLR-8382.
-
$43.00
Features Adapts to fuel system for use during pressure testingand diagnostic procedures. For use on 2003-Later 5.9L Cummins Diesel. Similar to OE part number MLR-9011.
-
$71.00
Features This IPR Socket actually combines two OE tools into one.Again, the configuration for the IPR changed in 2005 and asecond tool was developed for the change. However, ourAftermarket engineers worked with specialized technicians todevelop one tool that can address either version of the IPR? giving today’s technicians a cost-effective tool.
-
$42.00
Features This pair of High Pressure Fuel Rail Adapters is required toconnect to the vehicle’s fuel line. The fuel line connectionchanged in 2004 ? so the two adapters give you thecapability to address either platform for pressure testing.
-
$91.00
Features Installs the front crank seal with the cover on or offthe engine. The bolt is threaded into the crankshaft and the nut istightened to seat the seal. Similar to EN-50820 & EN48034. Applications: 2013-14 Cadillac ATS, 2014 Cadillac CTS,2013-14 Chevrolet Malibu, 2014 Chevrolet Impala and BuickRegal 2.0L and 2.5L engines.
-
$178.00
Features Ensure replacement injectors and seals are installedcorrectly. This kit installs the Teflon seal onto the end of theinjector. The pilot cone is placed onto the end of the injectorand the seal is started over the cone. The installer pushes the seal into the groove on theinjector tip. Applications include: 1998 – 2014 GM engines…
-
$203.00
Features Ensure replacement injectors and seals are installedcorrectly. This kit installs the dual seals onto the end of theinjector. These seals must be installed into their grooves, andthen sized to the engineered dimension before the injectorsare installed into their bores in the cylinder head Applications include 2010-later GM engines found in manyBuick, Cadillac, Chevrolet and…
-
$345.00
Features Save time removing crankshaft rear seals, preventingdamage to the block and crank. This seal remover is a special puller with three jawsdesigned to grab the inner lip of the seal. The forcing screw attached to the center plate is usedto react against the crankshaft end to pull the seal out. Eliminates damage to the…
-
$292.00
Features Makes replacing engine drive belts and startergenerators easier. This tool compresses the belt tensioner spring duringengine drive belt replacement and starter generatorservicing. Applications include 2.4L GM eAssist engines found in:2012 – 2016 Buick LaCrosse, 2012 – 2017 Buick Regal, 2011 -2014 Chevrolet Malibu
-
$29.00
Features Two-piece kit includes tools to properly size the sealand install the seals in the proper groove on the injectortip for leak-free operation. Works to install both seals on the injector tip. Similarto EN-51105. Applications: 2014-15 Chevrolet Silverado & GMC SierraV6 and V8, 2015 Chevrolet Suburban/Tahoe, GMC Yukon/XL, 2014Chevrolet Corvette, 2015 Cadillac Escalade.
-
$174.00
Features Used for removal of the direct injection fuel railwithout damage. The rail assembly must be removed as straight aspossible to prevent damaging an injector bore in thecylinder head or the mount assembly. Similar to EN-49248. Applications: 2007-2014 General Motors Direct InjectionEngines including those used in Pontiac, Saturn, Cadillacand Chevrolet vehicles.