Showing 21–40 of 121 results
-
$78.00
Features Power Steering Evacuation Cap allows for removal of air fromthe power steering system when used with a vacuum pump. Airin the system can cause noise and premature pump failure. Fits various power steering pump reservoirs. Similar to 211-265.
-
$160.00
Features The OTC 6867 Hub Seal Installer is used to install the wheelhub oil seal on single or dual wheel axle assemblies. Theseal installer adapter is driven with the 7″ detachablehandle. Applications with Ford, Lincoln and/or Mercury vehiclesusing the following axles:1999-later DanaFord 10-1/2″ Full Floating Axle. Similar to OE part numbers 205-422 and 205-153.
-
$110.00
Features Designed to be used with EVAP system tester. Includes a male tank adapter and female cap adapterconnected by a 20″ hose. Applications include:2006-Later Chrysler/Dodge/Jeep vehicles1999-2003 Mitsubishi Gallant2001-2005 Mitsubishi Eclipse Spyder Similar to OE part number MLR-8382.
-
$43.00
Features Adapts to fuel system for use during pressure testingand diagnostic procedures. For use on 2003-Later 5.9L Cummins Diesel. Similar to OE part number MLR-9011.
-
$91.00
Features Installs the front crank seal with the cover on or offthe engine. The bolt is threaded into the crankshaft and the nut istightened to seat the seal. Similar to EN-50820 & EN48034. Applications: 2013-14 Cadillac ATS, 2014 Cadillac CTS,2013-14 Chevrolet Malibu, 2014 Chevrolet Impala and BuickRegal 2.0L and 2.5L engines.
-
$178.00
Features Ensure replacement injectors and seals are installedcorrectly. This kit installs the Teflon seal onto the end of theinjector. The pilot cone is placed onto the end of the injectorand the seal is started over the cone. The installer pushes the seal into the groove on theinjector tip. Applications include: 1998 – 2014 GM engines…
-
$29.00
Features Two-piece kit includes tools to properly size the sealand install the seals in the proper groove on the injectortip for leak-free operation. Works to install both seals on the injector tip. Similarto EN-51105. Applications: 2014-15 Chevrolet Silverado & GMC SierraV6 and V8, 2015 Chevrolet Suburban/Tahoe, GMC Yukon/XL, 2014Chevrolet Corvette, 2015 Cadillac Escalade.
-
$174.00
Features Used for removal of the direct injection fuel railwithout damage. The rail assembly must be removed as straight aspossible to prevent damaging an injector bore in thecylinder head or the mount assembly. Similar to EN-49248. Applications: 2007-2014 General Motors Direct InjectionEngines including those used in Pontiac, Saturn, Cadillacand Chevrolet vehicles.
-
$76.00
Features Oversized retaining plates lock camshafts together attop dead center (TDC) on GM 2.8L 3.0L and 3.6L DOHC engines. Three-plate set is used to tighten both sets of cams toprevent them from turning while setting timing. Extra-large size prevents valve covers from beinginstalled with the plates in place, protecting the engine. Similar to EN-48383.
-
$232.00
Features Required tools to adjust and hold cam shaft timing on GM3.0 and 3.2 V-6 engines. Kit is designed to save shop time when servicing GM 3.0and 3.2 V-6 engines.
-
$376.00
Features Comprehensive tool kit designed to save time whenservicing GM 4-cylinder engines. Tools are actually easier to use than the original OEessential tools.Works on: GM 1988 to ’95 Skylark 2.3L , 1996 to ’98 Skylark 2.4L Chevrolet:1996 to ’04 Cavalier 2.4L2002 to ’05 Cavalier 2.2L DOHC2003 to ’05 Malibu 2.2L DOHC2002 to ’04 Classic 2.2L…
-
$128.00
Features Ensures camshaft is in proper position during servicing.Adapter plate is held in position with the supplied thumbscrew. Similar to 303-1565. Applications include engines found in Focus, Edge,Explorer, Escape, Taurus, Mustang, MKX, MKT, MKZ: 2010-later 2.0L Duratec 2010-later 2.0L EcoBoost 2012-later 2.0L GTDI 2015-later 2.3L EcoBoost 2016-later 3.5L EcoBoost
-
$70.00
Features Holds timing chain in place so water pump can be removedfor service. Special design allows easy installation regardless oftiming chain orientation. Simply remove access plate from front cover and installthe tool. Tool saves costly loss of timing on 2002-2008 GM 2.2Land 2.4L EcoTech motors found in Chevrolet, Oldsmobile,Pontiac, and Saturn platforms. GM water pump…
-
$42.00
Features Ford Oil Line Disconnect Tool Use to disconnect the high-pressure oil rail supply linefrom the fuel rail when removing fuel injectors. Works on the 6.0: diesel engine found in 2003-newerF-250, F-350, F-450, and F-550 trucks,and Ford Excursions.
-
$401.00
Features This tool installs the front and rear crankshaft wearsleeves and seals. It eliminates lip flare on the wear sleeve and installsthe seal properly. For use on Detroit Diesel Series 60 and two cycle 92engines. Similar to J35686B
-
$848.00
Features There is only one way to troubleshoot problem components ina heavy-duty power steering system: a flow and pressurereading meter. Measures both: 1 to 10 gallons oil flow and up to 3,000psi of pressure. When connected in line, this universalanalyzer will isolate the failed components in just minutes.There is no wasted time as in trial…
-
-
$66.00
Features Holds damper for removal and installation of the crank bolton most Honda/Acura engines. Can remove and install the damper so engine will notrotate. 4″ offset. 1/2″ square drive can be used with ratchet or breakerbar. 50mm hex with large center hole. Will fit around accessories eliminating additional partremoval. Proper fit for applications and allows…
-
$88.00
Features Fits tensioner pulleys with 13mm-16mm, 18mm hex or 3/8″ and1/2″ sq drives. 13mm and 15mm 12-point wrenches built intothe handle. 13mm, 14mm and 15mm crows foot wrenches alsoincluded.
-
$45.00
Features Designed for sealing GM power steering pumps witha two-tab cap design